Daewoo DP SP21 User Manual

INSTRUCTION MANUAL  
DP-SP22  
DP-SP21  
DP-SP20  
S
P
E
A
K
E
R
PLASMA MONITOR (DISPLAY)  
SPEAKER  
Thank you for purchasing the Daewoo Electronic Plasma Display Speakers. These  
speakers are specifically designed only for the Daewoo Plasma Display. To ensure the  
safe operation of the unit, please read these instructions before installing.  
PLASMA DISPLAY SPEAKER  
SPEAKER  
1. PLEASE CHECK THE  
FOLLOWING ITEMS  
SHOWN BELOW  
(2)  
M5 SCREWS  
VIBRATION ABSORBENT SPONGE  
S
P
E
A
K
E
R
(2)  
(16)  
SPEAKER WIRES  
SPECIAL SCREWS  
/ ROUND HEAD SCREWS  
(2)  
(4)  
STAND  
FIXED BRACKETS  
(2)  
(4)  
2
2. IMPORTANT SAFETY INSTRUCTIONS  
PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY  
PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT.  
WARNING : Disregarding these instructions can result in serious injury.  
WARNING  
CAUTION : Disregarding these instructions will result in the mistreatment of  
the unit and can result in injury or damage to the unit.  
CAUTION  
Do not leave out any part when assembling.  
Please install all parts as indicated.  
Do not use any parts other than those  
enclosed.  
(Doing so may cause the unit to fall and break)  
Do not alter or modify any parts  
(Failing to do so may cause the unit to vibrate and to fall)  
Do not use the speakers with other products.  
These speakers are specifically manufactured to be  
used with the Daewoo Plasma display to enhance  
your listening pleasure.  
(Failing to do so may cause the unit to fall and break)  
(Failing to do so can damage the speaker circuits resulting in fire)  
Do not allow a child to cling from or climb unto  
the speakers  
Do not place the speakers on sloped or  
unstable surfaces.  
(Doing so may cause the speakers to fall off or  
tip over causing injury and damage.)  
(It can cause electric shock or injury to the child)  
3
PLASMA DISPLAY SPEAKER  
PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING  
*
When assembling, be sure to use the enclosed  
Please be careful not to stain the speakers with  
parts and make sure all parts are tightly  
any gas or oil.  
screwed as instructed.  
(Failing to do so will cause the speakers to  
(Doing so will change the outer appearance)  
vibrate and unable to produce clear sound.)  
S
P
E
A
K
E
R
Do not place the speakers near heating units.  
Do not place the speakers in a humid or dusty  
place.  
Dusty  
(Failing to do so may alter the units)  
(Failing to do so will damage the speakers)  
Do not place speakers near a humidifier, or  
cooking pots where speakers will be exposed  
to steam or smoke.  
Please be sure to connect (+) inputs and (-)  
inputs correctly when connecting speakers to  
plasma display.  
Steam  
Smoke  
(Failing to do so may cause discoloration or  
damage to speakers)  
(If not connected correctly, it may result in distorted sound)  
4
3. ASSEMBLING INSTRUCTIONS  
USING SPEAKERS WHEN ATTACHED TO THE PLASMA DISPLAY  
ATTACHING VIBRATION ABSORBENT SPONGES TO SPEAKERS  
1
.
.
Clean the surface with soft, lint-free cloth  
where sponges will be attached.  
Attach the sponge to the side of the  
speaker that will be attached to the  
plasma display.  
5mm  
Note  
Please leave a 5 mm space on the top  
and bottom when attaching. Do not  
cover the entire side with the sponge  
as shown in the picture above.  
5mm  
INSTALLING FIXED BRACKETS TO SPEAKERS  
2
.
Install fixed brackets to speakers before  
attaching speakers to plasma display.  
Fixed brackets  
Note  
Please make sure which side the fixed  
brackets will be screwed to,  
considering the left and right side of  
speakers as shown in the picture to  
the left.  
Sponge-attached side  
5
PLASMA DISPLAY SPEAKER  
INSTALLING SPEAKERS TO THE PLASMA DISPLAY  
3
.
Place a protective covering over the surface you will be working on and lay  
the plasma display as shown below.  
S
P
E
A
K
E
R
.
Take the speakers with fixed brackets to the back of the plasma display. Place the hooks onto  
the fixed brackets to the squared holes in the back of the plasma display.  
Hooks  
.
Now tightly secure the  
hooks with the M5 screws.  
Note  
.
Please be sure to secure the screws to avoid  
any shaking or looseness.  
6
CONNECTING SPEAKER WIRES  
4
.
Take the speaker wire(2) and use the red cord to connect to and fro (+) inputs,  
and use the black cord to connect to and fro (-) inputs.  
Note  
.
.
Please be sure to connect red cord with (+) and black with (-); otherwise,  
speakers will not produce clear sounds.  
Please retain the left over accessories.  
7
PLASMA DISPLAY SPEAKER  
USING SPEAKERS ON ITS OWN STAND  
INSTALLING SPEAKERS TO ITS OWN STAND.  
1
Please be sure to have  
the vibration absorbent  
sponge onto the side of  
the speaker where the  
stand will be attached.  
.
Use a coin to secure  
the special screws  
(round head screws)  
tightly.  
S
P
E
A
K
E
R
Coin  
Stand  
Note  
.
To avoid loose fitting, please be sure that screws are secured tightly.  
Otherwise, vibrating or distorted sounds may be produced.  
CONNECTING SPEAKER WIRES.  
2
.
Take the speaker wires (2) and use the red cord to connect to and fro (+) inputs,  
and use the black cord to connect to and fro (-) inputs.  
8

HP Hewlett Packard FX75 User Manual
Epson A882441 User Manual
Diamond Multimedia Radeon 9600XT User Manual
Dell E178WFP User Manual
Dell Computer Keyboard KM714 User Manual
Cypress STK12C68 5 User Manual
Cannon Lichfield 10906G User Manual
Avaya 2033 User Manual
Asus P5N7A VM User Manual
Amana AKS3640 User Manual